Sustainable Cement Utilization
[Enugu, Enugu State Nigeria]

FIG 4 Schematic explanation of Portland cement production

There are three fundamental stages in the production of Portland cement:
1. Preparation of the raw mixture
2. Production of the clinker
3. Preparation of the cement

The chemistry of cement is very complex, so cement chemist notation was invented to simplify the formula of common oxides found in cement. This  reflects the fact that most of the elements are present in their highest oxidation state, and chemical analyses of cement are expressed as mass percent of these notional oxides.

The raw materials for Portland cement production are a mixture (as fine powder in the 'Dry process' or in the form of a slurry in the 'Wet process') of minerals containing calcium oxide, silicon oxide, aluminium oxide, ferric oxide, and magnesium oxide. The raw materials are usually quarried from local rock, which in some places is already practically the desired composition and in other places requires the addition of clay and limestone, as well as iron ore, bauxite or recycled materials. The individual raw materials are first crushed, typically to below 50 mm. In many plants, some or all of the raw materials are then roughly blended in a "prehomogenization pile." The raw materials are next ground together in a rawmill. Silos of individual raw materials are arranged over the feed conveyor belt. Accurately controlled proportions of each material are delivered onto the belt by weigh-feeders. Passing into the rawmill, the mixture is ground to rawmix. The fineness of rawmix is specified in terms of the size of the largest particles, and is usually controlled so that there are less than 5%-15% by mass of particles exceeding 90 μm in diameter. It is important that the rawmix contains no large particles in order to complete the chemical reactions in the kiln, and to ensure the mix is chemically homogenous. In the case of a dry process, the rawmill also dries the raw materials, usually by passing hot exhaust gases from the kiln through the mill, so that the rawmix emerges as a fine powder. This is conveyed to the blending system by conveyor belt or by a powder pump. In the case of wet process, water is added to the rawmill feed, and the mill product is slurry with moisture content usually in the range 25-45% by mass. This slurry is conveyed to the blending system by conventional liquid pumps.

Rawmix blending

The rawmix is formulated to a very tight chemical specification. Typically, the content of individual components in the rawmix must be controlled within 0.1% or better. Calcium and silicon are present in order to form the strength-producing calcium silicates. Aluminium and iron are used in order to produce liquid ("flux") in the kiln burning zone. The liquid acts as a solvent for the silicate-forming reactions, and allows these to occur at an economically low temperature. Insufficient aluminium and iron lead to difficult burning of the clinker, while excessive amounts lead to low strength due to dilution of the silicates by aluminates and ferrites. Very small changes in calcium content lead to large changes in the ratio of alite to belite in the clinker, and to corresponding changes in the cement's strength-growth characteristics. The relative amounts of each oxide are therefore kept constant in order to maintain steady conditions in the kiln, and to maintain constant product properties. In practice, the rawmix is xl controlled by frequent chemical analysis (hourly by X-Ray fluorescence analysis, or every three minutes by prompt gamma neutron activation analysis). The analysis data is used to make automatic adjustments to raw material feed rates. Remaining chemical variation is minimized by passing the raw mix through a blending system that homogenizes up to a day's supply of rawmix (15,000 tonnes in the case of a large kiln).

Formation of clinker

FIG. 7 Precalciner kiln

FIG. 8 Typical clinker nodules

The raw mixture is heated in a cement kiln, a slowly rotating and sloped cylinder, with temperatures increasing over the length of the cylinder up to a peak temperature of 1400-1450 °C. A complex succession of chemical reactions take place (see cement kiln) as the temperature rises. The peak temperature is regulated so that the product contains sintered but not fused lumps. Sintering consists of the melting of 25-30% of the mass of the material. The resulting liquid draws the remaining solid particles together by surface tension, and acts as a solvent for the final chemical reaction in which alite is formed. Too low a temperature causes insufficient sintering and incomplete reaction, but too high a temperature results in a molten mass or glass, destruction of the kiln lining, and waste of fuel. When all goes to plan, the resulting material is clinker. On cooling, it is conveyed to storage. Some effort is usually made to blend the clinker, because although xlii the chemistry of the rawmix may have been tightly controlled, the kiln process potentially introduces new sources of chemical variability. The clinker can be stored for a number of years before use. Prolonged exposure to water decreases the reactivity of cement produced from weathered clinker.

The enthalpy of formation of clinker from calcium carbonate and clay minerals is ~1700 kJ/kg. However, because of heat loss during production, actual values can be much higher. The high energy requirements and the release of significant amounts of carbon dioxide makes cement production a concern for global warming. See "Environmental effects" below.