-
Fabrication Of Electrical Pop Corn Machine
-
-
-
CHAPTER FOUR
4.1 Precautions
Accident can be defined as an unexpected, unplanned and unpredicted event, which could cause loss of life, damage of properties and stoppage of work
Safety can also be defined as freedom from accident.
The following precaution are put in place when operating the machine.
Touching of hot pot during processing is not advisable
Line wire must not be touched with unprotected hands.
Broken glasses and frame should be properly disposed.
4.2 Theory of Design and Analysis
The diameters of the machine are as follows:
Length of frame => 510mm
Length of Base => 510
Diameter of bigger pot => 50mm
Diameter of smaller pot => 45mm
Height of frame =>710mm
Volume = L x B x H
V = 184671000
HEAT TRANSFER CONSTRUCTION
This is the method of heat transfer by which heat energy moves from a region of highest concentration of heat to that of lower concentration while the material for body in question remain at fixed point. Most metals allow heat energy to pass through them and are said to be good conductor of heat . Non metals such as woods cotton, paper and cock do not allow heat to pass through them, this ones are classified as good condition they differ in their ability to conduct heat. In order words, they need material medium for their propagation.
 
-
-
-
ABSRACT - [ Total Page(s): 1 ]ABSTRACTIron pop corn machine has being a machine that is fabricated to produce a large and reasonable amount of pop corn with a limited cost and of fast rate it is economical as it is known to be for average Nigerians and also as appetizer to meet the demand of the consumer, invention of this machine at very economical rate, its source of heat is an electric burner, with a very moderate height and a detachable aluminum pot and container to collect the pop corn, the fabrication of the pop corn ... Continue reading---
TABLE OF CONTENTS - [ Total Page(s): 1 ]TABLE OF CONTENTS Title Page Certification Dedication Acknowledgement Abstract Table of contents CHAPTER ONEINTRODUCTION 1.1 The Background of the Project 1.2 Literature Review 1.3 Specification of Problems 1.4 Requirement of Design 1.5 Condition for Use 1.6 Characteristics 1.7 Appearance CHAPTER TWO2.1 Description of component part 2.2 Body frame work 2.3 Material needed fo ... Continue reading---
CHAPTER ONE - [ Total Page(s): 1 ]CHAPTER ONEINTRODUCTION1.1 The Background of The ProjectThe basic aim of this project is to improve the quality and standard of production of a pop-corn machine and how its producing the popcorn. Therefore, it act or promote and improve production rate and limit the frying time, as much as it could performed and lastly production it in a sanitary condition. The design and construction of pop corn machine is brought from the perspective of its availability in market.Also this p ... Continue reading---
CHAPTER TWO - [ Total Page(s): 2 ]CHAPTER TWODESCRIPTION OF THE COMPONENT PARTS AND WORKING PRINCIPLE2.1 Description of Components Parts This comprises of the main body itself i.e the part and the equipment used in constructing the pop corn machine. Four legs -: this serve as lifting mechanism Sitting portion of the pot Aluminium pot-: this is the uppermost of the pot that is accommodating the com-steering Element:this is caled electric burner. Support pipe, steering pot and the stirrer 2.2 ... Continue reading---
CHAPTER THREE - [ Total Page(s): 1 ]CHAPTER THREE3.1 Assembly Assembly is a way of fussing or coupling split parts together to become whole. Assembly procedure of this project goes thus: - After work has been completed on the source of heat supply (electric burner). The aluminum pot, the pot was designed on where to sit which is bolted i.e couple together with the electric burner for its operation. The means of assembling by bolting or riveting makes it more turn to both pot and sources of heat. The container of ... Continue reading---
CHAPTER FIVE - [ Total Page(s): 1 ]CHAPTER FIVECONCLUSION AND RECOMMENDATIONS5.1 Conclusion After testing the machine, we discovered that we are able to pop higher amount of popped coin due to the fact that pot is bigger than the previous ones constructed. Stirrer touches all the botton part of the pot A detachable container is constructed so as to reduce the wastage of pop-corn when transferring from pot to the containers. Also my conclusions give me the room for production of high demand of pop-corn ... Continue reading---
REFRENCES - [ Total Page(s): 1 ]REFERENCES Abdul Qadir, B.L (2010) strength at materials “I†Edition, Published by SMS published and printing enterprises, Ilorin page1-20, page 37/38.(P.N OKEKE and M.W Anyakqwha (1987&1989), Senior Secondary School Physics, Revised Edition, Macmillan Education LTD, London and Basingstoke, page 17.R.A Higgins, (1994) “Properties of engineering materials†Second Edition, Edward Arnold, a division of Hodder Headline PLC, 338 Euston Road, London, page 378. ... Continue reading---
-
ABSRACT - [ Total Page(s): 1 ]ABSTRACTIron pop corn machine has being a machine that is fabricated to produce a large and reasonable amount of pop corn with a limited cost and of fast rate it is economical as it is known to be for average Nigerians and also as appetizer to meet the demand of the consumer, invention of this machine at very economical rate, its source of heat is an electric burner, with a very moderate height and a detachable aluminum pot and container to collect the pop corn, the fabrication of the pop corn ... Continue reading---
CHAPTER FOUR -- [Total Page(s) 1]
Page 1 of 1
CHAPTER FOUR -- [Total Page(s) 1]
Page 1 of 1