-
Fabrication Of Aluminium Window
-
-
-
ABSTRACT
Privacy and security are major essential human needs in various homes, offices e.t.c. Accessibility to adequate, durable, fashionable and affordable windows in our different buildings has been a problem to the society. Ability to have access to window of good quality and high durability of a price affordable to an average Nigerian has been a problem.
This project here aims at production of a durable aluminium window. The aluminium window was subjected to different test, it was found to be efficient and has strength to provide adequate security at affordable price.
-
-
-
LIST OF FIGURES - [ Total Page(s): 1 ]LIST OF FIGUREFig1: Isometric view of the Aluminum window Fig2: Isometric drawing of the complex window ... Continue reading---
TABLE OF CONTENTS - [ Total Page(s): 1 ]TABLE OF CONTENTTitle page Approval page Dedication Acknowledgement Abstract Table of content List of figures Nomenclature CHAPTER ONE 1.0 Introduction 1.1 The Need for Aluminium Window CHAPTER TWO2.0 Literature Review 2.1 Aims and Objectives 2.2 Types of Window Manufactures 2.2.1 Single Hung and Double Hung Window 2.2.2 Casement Window 2.2.3 Bow ... Continue reading---
List of symbols/Abbreviations - [ Total Page(s): 1 ]NOMENCLATURE S/N SYMBOLS MEANING UNITS 1. V volume m3 2. M mass kg 3. P density Kg/m3 4. G acceleration due to ... Continue reading---
CHAPTER ONE - [ Total Page(s): 1 ]CHAPTER ONE1.0 INTRODUCTION OF ALUMINIUM WINDOWWindows are possibly most complex and interesting element in residential design. Today’s energy efficient window can dramatically decrease the heating and cooling costs while increasing the occupant comfort and minimizing window surface condensation problem. In recent years there have been the advances in windows of both new construction and retrofits. High performance windows system may be considered as one of the key factors for reach ... Continue reading---
CHAPTER TWO - [ Total Page(s): 2 ]CHAPTER TWO2.0 LITERATURE REVIEW In the past, windows were made by the use of wood as means of locking but it did not give a maximum security for life and properties and also it does not meet the wants of people.As time want on, technology came and they took it into consideration and decided to find alternative way to gives birth to aluminum windows, metal window e.t.c.These aluminum windows have been done in many ways with different designs irrespective to the wants of the prospective buy ... Continue reading---
CHAPTER THREE - [ Total Page(s): 3 ]CHAPTER THREE3.0 SELECTION OF MATERIALAn engineer is always facing a lot of problems, when it comes to the aspect of material selection. An Engineer is always limited to the material at its vicinity particularly in Nigeria there is the need for them to improvise with the little materials.There are some parameters that an engineer must consider before choosing certain materials, some of which are listed below:1. Physical properties2. Strength 3. Fabricability4. Economic cost5. Chemical comp ... Continue reading---
CHAPTER FOUR - [ Total Page(s): 5 ]CHAPTER FOUR4.0 DESIGN CALCULATION By considering the factor considered for the selection of materials and dimensions of window fixture [i.e installation points], the calculation carried out was.4.1 MASS CALCULATION OF THE COMPONENTS For the frame unit.Volume V1 of track of the frame = LxBxT ... Continue reading---
CHAPTER FIVE - [ Total Page(s): 3 ]CHAPTER FIVE5.0 FABRICATION DETAILS5.1 CUTTING LIST OR MATERIAL LISTCUTTING LIST PER FRAME UNIT (ANGLE ALUMINUM)2†X 1†X 1200mm……………2 Off2†X 1†X 1178mm……………1 OffCUTTING LIST PER SLIDING UNIT2†X 1†X 517mm……………2 Off (top slide)2†X 1†X 517mm……………2 Off (bottom unit)2†X 1†X 1150mm………â ... Continue reading---
CHAPTER SIX - [ Total Page(s): 1 ]CHAPTER SIX6.0 CONCLUSION AND RECOMMENDATION6.1 CONCLUSIONWe sincerely appreciate the immense effort of the polytechnic authority for including this programme at the end of the course to help increase the knowledge and also the student scope of reasoning in terms of technological developmentThis project allocated to students along with the course of completing the National Diploma Certificate (ND) is of vital and great importance because it improves the student’s knowledge to ... Continue reading---
REFRENCES - [ Total Page(s): 1 ]REFERENCESAbolarin Thomas (2007): Machine tools and technologyâ€, ND II Mechanical engineering Handout, Kwara State Polytechnic, Ilorin, Nigeria (unpublished), pg 32.Chapman W. A .J (2000) “workshop technology’, 2nd edition Arnold London , pp 100-104Komolafe Abiola, Ajagbe M. Solomon (2011), “A project report on construction of aluminium frame, Pg 11, 22-24.Ojo A.I (1997),‘’Design and construction of a metal flush door’’, ND project report submi ... Continue reading---
-
LIST OF FIGURES - [ Total Page(s): 1 ]LIST OF FIGUREFig1: Isometric view of the Aluminum window Fig2: Isometric drawing of the complex window ... Continue reading---
ABSRACT -- [Total Page(s) 1]
Page 1 of 1
ABSRACT -- [Total Page(s) 1]
Page 1 of 1