-
Fabrication Of Metal Panel Door
-
-
-
CHAPTER THREE
3.0 DESCRIPTION OF COMPONENT PARTS AND WORKING PRINCIPLE
3.1 DESCRIPTION OF COMPONENT PARTS
3.1.1 The Frame
This is the unit that is fasted and locked to the wall and also held to the movable door panel.
It must be connected to the wall in order to withstand all the load due to oscillatory door panel and the jam-lock.
3.1.2 The Latches
These units are used to lock from inside after closing the door during the night or when outing. They are also fabricated to the metal panel door.
3.1.3 Panel Unit
This is the unit that is fabricated to the frame units. It is the main part of the door and also the movable part of metal panel door after the frame have been fastened and locked to the wall.
3.1.4 Handle
The handle provides easy control of opening and closing of the metal door. It is used to push and pull of the door.
3.2 WORKING PRINCIPLE
Doors are design to close and open with the aid of hinges. This mechanism fails tom function and sometimes noisy when the hinges get corrected. A stopper is fabricated on the frame for the purpose of moving the door inward.
When the correct key is inserted, the gap between the key pin and the drivers pin along with the edge of the plug called the shear line.
A lock from locking device which hooked hole created on the door frame is released and the door open when the correct key is used.
-
-
-
ABSRACT - [ Total Page(s): 1 ]ABSTRACTSecurity of life and property cannot be over emphasized. Human beings need privacy in their various homes and offices which necessitate the need for doors among other security service. To has been a major challenges for the people to have door of high quality and that are also durable at affordable prices by an average Nigerian. This project was done purposely to fabricate a metal panel door of high quality capable of giving maximum securities to life and properties at affordable price. ... Continue reading---
TABLE OF CONTENTS - [ Total Page(s): 1 ]TABLE OF CONTENTSTitle pageApproval pageDedicationAcknowledgementAbstractsCHAPTER ONEIntroductionDefinitionTypesNeed for metal panel doorAims and objectivesCHAPTER TWO2.00 Analysis of alternative method and choice of best alternatives2.10 Types of door mechanism2.20 Literature reviewCHAPTER THREE3.0 General description of component and it working principle3.1 Description of component part.3.1 Working principleCHAPTER FOUR4.0 Design CalculationCHAPTER FIV ... Continue reading---
CHAPTER ONE - [ Total Page(s): 2 ]CHAPTER ONE1.0 INTRODUCTIONMany years ago, different types of doors were in use, which includes doors made of woods or grasses. These doors were made to meet the purpose of security to both life and properties. It was later discovered that doors made of wood do not last longer. They have short life span and they can easily get burnt. More so, considering the rate at which armed robbers break into houses in our society, one would regret that wooden doors and grass doors gave them the chance ... Continue reading---
CHAPTER TWO - [ Total Page(s): 2 ] Sliding door: sliding door is often useful to have doors which slide along tracks often for space or aesthetic consideration Dutch door or stable door: the top half of the door operates independently from the button half. Swing door: Swing door has special hinges that allow it open either outward or inwards and is usually spring to keep it closed Self butting door is called as such because of its special hinges that permit panel leaf to ... Continue reading---
CHAPTER FOUR - [ Total Page(s): 3 ]CHAPTER FOUR4.1 DESIGN CALCULATION FOR METAL DOORParameter of the door frameBreadth (B) =1220mmLength (L) =2135mmArea of the frame= length x breath ... Continue reading---
CHAPTER FIVE - [ Total Page(s): 1 ]CHAPTER FIVE5.0 SELECTION OF MATERIAL, FABRICATION DETAIL AND ASSEMBLY.SELECTION OF MATERIAL: when it comes to selection of material both engineer and technician can face a lot of problem, because any material to be selected for a particular work must meet up with the requirement of the output i.e. the right material should be selected for the right job. In selection of any material in engineering, the material to be selected must meet the following properties:ï¶ Mechanical ... Continue reading---
CHAPTER SIX - [ Total Page(s): 1 ]CHAPTER SIX6.0 CONCLUSION AND RECOMMENDATION6.1 CONCLUSION The project fabrication of metal panel door was embarked upon to solve the problem of short lifespan of door also to update the design of door which serves as an entrance to a building. It was taken into consideration, metal door or metal panel door is an indispensable types of door, this is because this types of door is made of metal which passes/ exhibit some certain properties such as mechanical properties which include plastici ... Continue reading---
REFRENCES - [ Total Page(s): 1 ]REFERENCEEyiowukawi O. S. (2012) fabrication of metal panel door, ND project report submitted to the department of mechanical engineering, Kwara State Polytechnic, Ilorin (unpublished).Kayoed A. and Omotuase O.L (2006). Fabrication of metal panel door, ND project report submitted to the department of mechanical engineering, Kwara State Polytechnic, Ilorin (unpublished).Olagoke S.A (2008)†properties of material†4th Edition S. A. multiventures Ibadan.Orisabinon .T.J. and Alowosile, S ... Continue reading---
-
ABSRACT - [ Total Page(s): 1 ]ABSTRACTSecurity of life and property cannot be over emphasized. Human beings need privacy in their various homes and offices which necessitate the need for doors among other security service. To has been a major challenges for the people to have door of high quality and that are also durable at affordable prices by an average Nigerian. This project was done purposely to fabricate a metal panel door of high quality capable of giving maximum securities to life and properties at affordable price. ... Continue reading---
CHAPTER THREE -- [Total Page(s) 1]
Page 1 of 1
CHAPTER THREE -- [Total Page(s) 1]
Page 1 of 1