-
Fabrication Of Metal Panel Door
-
-
-
CHAPTER SIX
6.0 CONCLUSION AND RECOMMENDATION
6.1 CONCLUSION
The project fabrication of metal panel door was embarked upon to solve the problem of short lifespan of door also to update the design of door which serves as an entrance to a building.
It was taken into consideration, metal door or metal panel door is an indispensable types of door, this is because this types of door is made of metal which passes/ exhibit some certain properties such as mechanical properties which include plasticity, hardness, malleability, ductility rigidity e.t.c. and physical properties which includes: thermal, melting point, conductivities e.t.c. that makes it resistance to some vicinity or environmental attack such as water, temperature, termite, humidity, harm than and external forces i.e. push and pull forces which causes deformation of shapes and structure of the door after short period of time.
Apart from it gives maximum security to lives and properties, metal door play a wider /crucial role in having advantages over wood and glass doors. It gives effective means of giving house maximum security and is a modernized method of constructing a door.
Furthermore, it was discovered that doors made with wood do not last long and cannot withstand engineering stress {Eyiowukawi S.o [2012]}â€fabrication of metal panel door†ND project report submitted to department of mechanical engineering, Kwara state polytechnic ICS, Ilorin unpublished). Metal panel door is strong enough to withstand engineering stress.
Meanwhile this particular or perfect was constructed with metal. The design is genie unique and there is even the addition of lens to the design.
It is belief that, the present works had solved the above mentioned problems and also add beauty to doors i.e. It serves as ornamental to the building. Metal door had assisted and lower cost which is to be made for replacement of door in terms of shrinking effects of the doors during the winter period and reduce the strain effect on the door to constant push & pull forces. In spite of the laudable function of the metal door, it is quite necessary to give adequate maintenance to the door by repainting the door whenever to original paint is fading off, and when the door is about to not due to constant contact with damp floor or surface.
Finally, the experience gained by the student during the fabrication of this projects, student can now embarked on it and decide to fabricate it in mass quality which can also serves as source of income to him/her it also reduce of unemployment in our society region and our country because when looking at Nigeria as a country in this days it is cleared to everyone that the economics of this country is depreciating it is falling and not rising so this project when putting it into practice can banish unemployment and give room to employing of workers ( By Olaiya Metal Work (2016)
6.2 RECOMMENDATION
The wealth of any society is determined by the variety and quality of the articles it posses for it use and consumption. All the material things we posses are made from the earth or from nature. Meanwhile our prosperity depends upon on our ability to convert these raw materials into useful articles of consumption. Prior to this I will want to recommend that serious attention should be give to engineering. This will go a long way in adding value to the wealth of our society.
Furthermore, student of engineering should be gives deep knowledge of the machine in the work shop most especially the ND students. It is believer that, this will give them the preamble knowledge and skills needed by the time they come back HND. For student to continue playing a major role in the fabrication process, then it is virtually important to motivate and encourage students more on how to use modern equipment/materials for fabrication. The student should try to devote their time on workshop for practical works which will improve the student educational skill on fabrication process.
Appropriate knowledge and practical work should be impact to student in design and fabrication of projects should be made available in abundant and be in good conditional to reduce the fatigue of the student during fabrication process ( Engineer Amusa (T.A) 2015 SIWES coordinator lower Niger River Basin Development Authority, Ilorin (LNRBDA) the supervisor should make sure all students participate because it bridge the gap between theory been done in class and also improve the practical knowledge of student (Orinsabinone,Toba Joh, Awosile and Shola John fabrication of metal doors ND project report submitted to department of mechanical engineering, Kwara state polytechnics, Ilorin ( unpublished ).
-
-
-
ABSRACT - [ Total Page(s): 1 ]ABSTRACTSecurity of life and property cannot be over emphasized. Human beings need privacy in their various homes and offices which necessitate the need for doors among other security service. To has been a major challenges for the people to have door of high quality and that are also durable at affordable prices by an average Nigerian. This project was done purposely to fabricate a metal panel door of high quality capable of giving maximum securities to life and properties at affordable price. ... Continue reading---
TABLE OF CONTENTS - [ Total Page(s): 1 ]TABLE OF CONTENTSTitle pageApproval pageDedicationAcknowledgementAbstractsCHAPTER ONEIntroductionDefinitionTypesNeed for metal panel doorAims and objectivesCHAPTER TWO2.00 Analysis of alternative method and choice of best alternatives2.10 Types of door mechanism2.20 Literature reviewCHAPTER THREE3.0 General description of component and it working principle3.1 Description of component part.3.1 Working principleCHAPTER FOUR4.0 Design CalculationCHAPTER FIV ... Continue reading---
CHAPTER ONE - [ Total Page(s): 2 ]CHAPTER ONE1.0 INTRODUCTIONMany years ago, different types of doors were in use, which includes doors made of woods or grasses. These doors were made to meet the purpose of security to both life and properties. It was later discovered that doors made of wood do not last longer. They have short life span and they can easily get burnt. More so, considering the rate at which armed robbers break into houses in our society, one would regret that wooden doors and grass doors gave them the chance ... Continue reading---
CHAPTER TWO - [ Total Page(s): 2 ] Sliding door: sliding door is often useful to have doors which slide along tracks often for space or aesthetic consideration Dutch door or stable door: the top half of the door operates independently from the button half. Swing door: Swing door has special hinges that allow it open either outward or inwards and is usually spring to keep it closed Self butting door is called as such because of its special hinges that permit panel leaf to ... Continue reading---
CHAPTER THREE - [ Total Page(s): 1 ]CHAPTER THREE3.0 DESCRIPTION OF COMPONENT PARTS AND WORKING PRINCIPLE 3.1 DESCRIPTION OF COMPONENT PARTS3.1.1 The Frame This is the unit that is fasted and locked to the wall and also held to the movable door panel. It must be connected to the wall in order to withstand all the load due to oscillatory door panel and the jam-lock.3.1.2 The Latches These units are used to lock from inside after closing the door during the night or when outing. They are a ... Continue reading---
CHAPTER FOUR - [ Total Page(s): 3 ]CHAPTER FOUR4.1 DESIGN CALCULATION FOR METAL DOORParameter of the door frameBreadth (B) =1220mmLength (L) =2135mmArea of the frame= length x breath ... Continue reading---
CHAPTER FIVE - [ Total Page(s): 1 ]CHAPTER FIVE5.0 SELECTION OF MATERIAL, FABRICATION DETAIL AND ASSEMBLY.SELECTION OF MATERIAL: when it comes to selection of material both engineer and technician can face a lot of problem, because any material to be selected for a particular work must meet up with the requirement of the output i.e. the right material should be selected for the right job. In selection of any material in engineering, the material to be selected must meet the following properties:ï¶ Mechanical ... Continue reading---
REFRENCES - [ Total Page(s): 1 ]REFERENCEEyiowukawi O. S. (2012) fabrication of metal panel door, ND project report submitted to the department of mechanical engineering, Kwara State Polytechnic, Ilorin (unpublished).Kayoed A. and Omotuase O.L (2006). Fabrication of metal panel door, ND project report submitted to the department of mechanical engineering, Kwara State Polytechnic, Ilorin (unpublished).Olagoke S.A (2008)†properties of material†4th Edition S. A. multiventures Ibadan.Orisabinon .T.J. and Alowosile, S ... Continue reading---
-
ABSRACT - [ Total Page(s): 1 ]ABSTRACTSecurity of life and property cannot be over emphasized. Human beings need privacy in their various homes and offices which necessitate the need for doors among other security service. To has been a major challenges for the people to have door of high quality and that are also durable at affordable prices by an average Nigerian. This project was done purposely to fabricate a metal panel door of high quality capable of giving maximum securities to life and properties at affordable price. ... Continue reading---
CHAPTER SIX -- [Total Page(s) 1]
Page 1 of 1
CHAPTER SIX -- [Total Page(s) 1]
Page 1 of 1